It often ends up with erratic key presses, repeating or not it’s even not working. Flirc is an USB dongle which presents itself as a keyboard. So in theory you can use the default keyboard setup with Kodi and have Flirc do the task of translating the codes to key presses. Should be simple without any messing around with Flirc (as I’m writing about Kodi on a raspberry Pi)…? It still takes some time to get it to work and with this post I’d like to share my experiences how I got I did this.įirst of all, I created an activity in the Harmony software and added a multimedia PC keyboard. I just took a HP machine and then you have a nice mapping with all the keys you need. I don’t know how the others will do but here’s a link to get you started: Ebay It turned out that the codes from Logitech’s database were causing most of the problems and I used a cheap MCE remote (from Ebay) to learn all the keys: Now comes an important part, it turns out that the keys are working, but just as stated above, the behaviour was erratic and I ended up with a setup which I couldn’t use. Or maybe selecting another MCE remote setup from Logitech’s database works just fine for you? Please note: I don’t say that you have to use a MCE remote, maybe it will work just fine with another remote which you already have. I assume that you’re aware how you can setup an activity in the Logitech remote so configure the remote with the MCE machine as the “video device”. Check the “Customise buttons” option and make sure that all buttons, that you want to use, are mapped to the MCE device. When ready, Update the remote and enter the activity when everything’s ready so you can program the Flirc dongle. So, startup the Flirc utility, which you already should have installed from the Flirc downloads page, and check the file menu and update the firmware if there’s a newer version available. You’re now ready to start programming the keys described by the Kodi documentation Then, select full keyboard from the controllers menu and now the screen looks like this: I also recommend that you select the clear configuration option from there as well. So, for example, map the STOP key to the X by pressing the X on the virtual keyboard and press your stop on your Logitech’s remote while it’s pointed at the Flirc dongle. So, when you press the STOP button the X key lights up in the Flirc desktop application. When you’re done programming you can check the behaviour by opening a text editor on your computer and press all the keys to see if they’ve been mapped correctly and correct them if necessary. Now there’s another important setting in the Flirc tool under the file / advanced settings: Configure the Inter-Key Delay to 5 or higher as shown here.Īt the moment, I can’t recommend using the other settings but your mileage may vary. Now you’re good to go to do some testing with Flirc attached to your Kodi machine. In my case, I first used an USB cable to get the Flirc receiver in the line of site of my remote sitting just next to my plasma TV. This turned out to be a problem as the plasma tv turned out to be interfering with the IR signal making control of Kodi difficult. So then I placed the receiver further backwards to get some more shielding from my TV.įor me, most keys now worked just fine although some still gave problems. I used the Kodi Kodi keymap addon to map the not working keys thus deviating from the original Kodi keymap in a couple of cases. The addon is a very useful tool to map more functions to your Harmony. FLIRC HARMONY KODI FULLįor example, I mapped the 7 and 8 keys to subtitle delay and forward under full screen playback so you can use them for other purposes in an other Kodi activity. I am now developing this using OpenHAB.Ok, but first, Kodi needs to function with the basic remote keys and it turned out that some extra settings need looked into.Īs Logitech writes on their site the remote is often configured to repeat commands which some receivers need to work correctly. I had worked out a way that I can control all the functions of Kodi via Google Home, but it relied on IFTTT, which can be very unreliable TBH. It always works out of the box, there is no setup required. I don't actually use OSMC, I use LibreELEC on a Raspberry Pi and vanilla Kodi on a Linux and Windows PCs. The OSMC remote just controls the basic functions of Kodi. It is up to you what functions you control in this way. If I want to switch back to Kodi I say "Hey Google, Switch to Kodi". If I want switch the AVR's input to my Xbox One all I have to say is "Hey Google, switch to the Xbox". So I can say "Hey Google, Turn on the Lounge TV" and a Google Home routine will turn on the AVR and TV. I have programmed the Broadlink app with the remote functions I want to control. The Broadlink app is synced with Google Home. I use Google Home, a Broadlink RM Mini 3 and the official OSMC remote to control Kodi, my AVR and my TV.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |